Cross-Connection Control Program
Cross-Connection Control Program Overview
Your local water provider is making improvements to protect the safety of drinking water. Here’s why.
A cross-connection is an actual or potential connection between the safe drinking water (potable) supply and a source of contamination or pollution. Cross-connections can result in a hazardous event known as backflow, which can draw those contaminants into your drinking water supply.
North Carolina Administrative Code Title 15A, Subchapter 18C, Section 0406, Subsection B states that “no person shall construct, maintain, or operate a physical arrangement whereby a public water system has a cross-connection without the use of proper backflow protection.
Step 2
Postal Notification
Hydrocorp sends notifications informing water customers of plumbing code requirements that backflow preventers must be tested annually. Facility Assessments/ Inspections for Cross-Connection Hazards are required as specified within the local CCC plan. Instructions and due dates are included in notifications.
Step 1
Hydrocorp Assistance
Hydrocorp hired by local water purveyor to assist with mandatory Cross-Connection Control Program (CCC).
Step 3
Onsite Inspection/Survey
Water Customer selects and hires an ASSE approved Backflow Preventer Tester and/or Cross-Connection Inspector. Test and Inspection data are submitted online to the local water purveyor/utility.
Step 4
Data/Corrective Action
If cross-connections are identified during the inspection, the water customer is provided written instructions for modifications and a mandatory compliance date.
Step 5
Compliance Verification
Annual Backflow preventer test and inspection records confirmed and maintained by the local water purveyor as required by law
Step 1
Hydrocorp Assistance
Hydrocorp hired by local water purveyor to assist with mandatory Cross-Connection Control Program (CCC).
Step 2
Postal Notification
Hydrocorp sends notifications informing water customers of plumbing code requirements that backflow preventers must be tested annually. Facility Assessments/ Inspections for Cross-Connection Hazards are required as specified within the local CCC plan. Instructions and due dates are included in notifications.
Step 3
Onsite Inspection/Survey
Water Customer selects and hires an ASSE approved Backflow Preventer Tester and/or Cross-Connection Inspector. Test and Inspection data are submitted online to the local water purveyor/utility.
Step 4
Data/Corrective Action
If corrective action is identified during the facility Cross-Connection Inspection, the water customer is provided written instructions and a mandatory compliance date.
Step 5
Compliance Verification
Annual Backflow preventer test and inspection records confirmed and maintained by the local water purveyor as required by law
RESIDENTIAL WATER CUSTOMERS
Cross-Connection and Backflow FAQ
PART I: INSPECTIONS / SURVEYS
A cross-connection is an actual or potential connection between the safe drinking water (potable) supply and a source of contamination or pollution. State plumbing codes require approved backflow prevention methods to be installed at every point of potable water connection and use. Cross-Connections must be properly protected or eliminated.
A public water supplier may determine that specific residential water service connections shall be inspected (with appropriate notification in advance) for
potential cross-connection hazards. Causes for residential exterior inspections are lawn irrigation systems.
A typical residential exterior cross-connection inspection takes 5-15 minutes.
No.
Building owners are responsible for costs associated with corrective action/non-compliance.
If a residential service connection owner is notified of a mandatory inspection, compliance is required. These inspections are conducted in order to ensure compliance with state regulations to maintain the safety of your drinking water.
Penalties for refusing to cooperate with inspections and/or refusing to make needed repairs are determined by your local water utility. These typically can include termination of water service, a fine, or both.
PART II: BACKFLOW PREVENTION ASSEMBLY TESTING
PART III: GENERAL RESOURCES
Residential Cross-Connection Control Survey | Exterior from HydroCorp on Vimeo.
Example: Hose connection vacuum breakers |
Example: Integrated vacuum breaker on outside hose spigot. |
 Example: Hose end in bucket |  Example: Hose end in pool |
 |
Vacuum breaker should not be subject to continuous pressure like the example here illustrates. (This type of irrigation set up/system would need to be corrected.) |
These require periodic performance testing by a Certified Tester.
 Pressure Vacuum Breaker Assembly |  Reduced Pressure Principle Backflow Prevention Assembly |
Commercial Facility Water Customers
Cross-Connection and Backflow FAQ
PART I: INSPECTIONS / SURVEYS
A cross-connection is an actual or potential connection between the safe drinking water (potable) supply and a source of contamination or pollution. State plumbing codes require approved backflow prevention methods to be installed at every point of potable water connection and use. Cross-Connections must be properly protected or eliminated.
The North Carolina Administrative Code Section 15A NCAC 18C .0406 B states that “no person shall construct, maintain, or operate a physical arrangement whereby a public water system has a cross-connection without the use of proper backflow protection.” To ensure adherence to this code and to mitigate risk to the quality of the potable water system, the City of Weaverville is implementing a Cross-Connection Control Program, which includes onsite inspections for potentially hazardous interconnections.
Hose Connection Vacuum Breaker Video
Residential Cross-Connection Control Survey | Exterior from HydroCorp on Vimeo.
If your building has an exterior Testable Type Backflow Preventer Assembly (ASSE 1013 or ASSE 1015 type) in supply to the interior plumbing, your inspection may take less than 15 minutes. Prior to their arrival, be sure to inform the inspector if you have an exterior or interior backflow preventer assembly. Buildings with no existing backflow preventer at the water service connection point may require a more extensive inspection.
If your building has an exterior existing backflow preventer assembly, being present may not be necessary. Consult with the inspector/tester you hire prior to their visit for final determination.
If you are the owner of the facility being inspected, you are responsible for any needed repairs. Renters may have to refer to their lease agreements in order to determine whether they are responsible for repairs.
Yes. These inspections are conducted in order to ensure compliance with state regulations to maintain the safety of your drinking water.
Penalties for refusing to cooperate with inspections and/or refusing to make needed repairs are determined by your local water utility. These typically can include termination of water service, a fine, or both.
PART II: BACKFLOW PREVENTION ASSEMBLY TESTING
PART III: GENERAL RESOURCES
 Example: Hose connection vacuum breakers |  Example: Integrated vacuum breaker on outside hose spigot. |
Example: Hose end in bucket | Example: Hose end in pool |
|
Vacuum breaker should not be subject to continuous pressure like the example here illustrates. (This type of irrigation set up/system would need to be corrected.) |
These require periodic performance testing by a Certified Tester.
Pressure Vacuum Breaker Assembly | Reduced Pressure Principle Backflow Prevention Assembly |